For Invisi-Fast Biscuit part dimensions, click here.

Available in many different styles: NM-Clear, NM-Black, NMB, TXB, TT, TD, TQ, PC-1. Invisi-Fast™ NM-CLEAR or BLACK- works with several pre-grooved boards including Monarch, Fiberon, Veranda, Latitudes, Gossen, Moisture Shield, Perennial Decking and many others. Invisi-Fast NM also works on boards with machined in grooves that are cut using a standard biscuit jointer or router. This fastener is 1 7/8" wide. Provides 3/16” board spacing. Invisi-Fast™ TD-CLEAR was specifically designed to work with the Tigerdeck brand grooved boards. Provides 3/16” board spacing. Invisi-Fast™ TT-CLEAR was designed to perfectly compliment the Timber-Tech grooved boards. Provides 3/16” board spacing. Invisi-Fast™ TXB-BLACK fastener is compatible with Trex’s Transcends, Brasilia, Accents and Contours pre-grooved deck board. It also works with deckboards with at least 5/32" groove and would like a 1/4" spacing. Invisi-Fast™ TQ-CLEAR was designed to be used on 3/4” deck boards. You can choose deck board spacing of either 1/8” or 3/16”. Groove dimension should be 5/32” cut 1/2” deep(minimum). Invisi-Fast™NMB-BLACK was designed to work with deckboards with at least an 5/32" groove. It is 1 1/8" wide and provides a 5/32" spacing. IF YOU NEED SCREWS FOR METAL JOISTS PLEASE CONTACT US!

Invisi-Fast Biscuit Kit - 100 pc

100 Invisi-Fast Biscuit Fasteners, 100- 2 1/4" trim head screws, 1 Driver bit
Covers approx. 60 sq. feet (5.57 sq. m).

Kit with ACQ or Stainless Steel Screws

Invisi-Fast Biscuit Kit - 500 pc

500 Invisi-Fast Biscuit Fasteners, 500- 2 1/4" trim head screws, 1 Driver bit
Covers approx. 300 sq. feet (27.87 sq. m).

Kit with ACQ or Stainless Steel Screws

36 Count Start Clip Options

36- fasteners, screws, 1- Driver Bit

Kits available:
Kit with Original No Spacer Option(Plastic) for under deck attachment
Kit with steel fasteners for Trex grooved deck boards
Kit with steel fasteners for Any deckboard with 1/8" groove such as Timber-Tech, Veranda, ChoiceDeck, Moisture Shield, NyloDeck, Perrennial Wood and many more

Step 1: Install Invisi-Fast No-Spacer on ledger board.

Be sure overhang tabs are flush on top of ledger board. Use center screw location going into ledger unless wood imperfection is present. If the center screw hole cannot be used, use one of the other two available screw holes. The Invisi-Fast No-Spacer should be placed on the farthest edge near the outside corners and in-between the joists elsewhere. Where the two boards meet (butt joint) use one Invisi-Fast No-Spacer on either side of the joist underneath the deck board to secure the end of each board.

Step 2: Place the first deck board using the desired overhang. Install two screws into the deck board using the two holes provided in the underside of Invisi-Fast No-Spacer.

Make sure that the board is straight as the screws are tightened.

Step 3: Insert Invisi-Fast Biscuit fastener into the groove of the board, centering the fastener on joist. Tighten the screw only half way into joist. Be sure the screw is in the center of joist. Continue installing Invisi-Fast Biscuit fasteners in the center of each joist along the remainder of deck board.

Step 4: Slide next deck board firmly in place while aligning Invisi-Fast Biscuit fasteners into the groove. Install the next row of Invisi-Fast Biscuit fasteners into the groove of the second board as in Step 3. Before installing the screw, be sure deck board is snug to the fastener between board 1 and 2. Continue installing Invisi-Fast Biscuit fasteners in the center of each joist along the remainder of deck board.

Step 5: Tighten screws in first row between deck board 1 and deck board 2. Continue tightening screws along the remainder of deck board. Continue installing Invisi-Fast Biscuit fasteners into deck boards as in Steps 3 and Step 4.

Step 6: Use the standard Invisi-Fast No-Spacer on your first, last board and stairs to create a complete screw/nail free surface. Invisi-Fast No-Spacer sold separately.